Use my Search Websuite to scan PubMed, PMCentral, Journal Hosts and Journal Archives, FullText. Kick-your-searchterm to multiple Engines kick-your-query now !>

A dictionary by aggregated review articles of nephrology, medicine and the life sciences Your one-stop-run pathway from word to the immediate pdf of peer-reviewed on-topic knowledge.

10.1016/j.ohx.2020.e00130 http://scihub22266oqcxt.onion/10.1016/j.ohx.2020.e00130 32838090!7391241!32838090     free     free     free Warning: file_get_contents(https://eutils.ncbi.nlm.nih.gov/entrez/eutils/elink.fcgi?dbfrom=pubmed&id=32838090&cmd=llinks): Failed to open stream: HTTP request failed! HTTP/1.1 429 Too Many Requests in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 215 Deprecated: Implicit conversion from float 209.6 to int loses precision in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 534 Deprecated: Implicit conversion from float 209.6 to int loses precision in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 534 Deprecated: Implicit conversion from float 209.6 to int loses precision in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 534 Deprecated: Implicit conversion from float 209.6 to int loses precision in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 534 Deprecated: Implicit conversion from float 209.6 to int loses precision in C:\Inetpub\vhosts\kidney.de\httpdocs\pget.php on line 534       HardwareX 2020 ; 8 (ä): e00130 Nephropedia Template TP {{tp|p=32838090|t=2020. Open source high-temperature RepRap for 3-D printing heat-sterilizable PPE and other applications |pdf=|usr=}}{{32838090}} gab.com Text Open source high-temperature RepRap for 3-D printing heat-sterilizable PPE and other applications JO: HardwareX http://www.kidney.de/pget.php?&tw=1&pmid=32838090 #FOAvip Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1000, the Cerberus - an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200? degrees C-capable heated bed, ii) 500? degrees C-capable hot end, iii) isolated heated chamber with 1?kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5?MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization. Twit Text FOAVip Open source high-temperature RepRap for 3-D printing heat-sterilizable PPE and other applications ????HardwareX http://www.kidney.de/pget.php?&tw=1&pmid=32838090 #FOAvip Twit Text # Free Paper on # # # # # LINK http://www.kidney.de/pget.php?&tw=1&pmid=32838090 #FOAvip English Wikipedia <ref>{{Cite pmid|32838090}}</ref> Open source high-temperature RepRap for 3-D printing heat-sterilizable PPE and other applications #MMPMID32838090 Skrzypczak NG; Tanikella NG; Pearce JM HardwareX 2020[Oct]; 8 (ä): e00130 PMID32838090show ga Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1000, the Cerberus - an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200? degrees C-capable heated bed, ii) 500? degrees C-capable hot end, iii) isolated heated chamber with 1?kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5?MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization. äOpen source high-temperature RepRap for 3-D printing heat-sterilizable(epmc).pdf DeepDyve Pubget Overpricing